70 lines
3.0 KiB
Markdown
70 lines
3.0 KiB
Markdown
# BigTreeTech BTT002/TMC2209 Config for Prusa MK3S
|
|
|
|
## Requirements
|
|
- [Prusa MK3S](https://www.prusa3d.com/original-prusa-i3-mk3/) or MK3 with MK3S upgrade (required for filament runout to work properly)
|
|
- BigTreeTech BTT002 motherboard
|
|
- 4 x BigTreeTech TMC2209s (DIAG pin location differs from Watterott's & similar designs)
|
|
|
|
## Upgrade Notes
|
|
* ⚠️ Cut or desolder the Z & E driver DIAG pins or they will interfere with PINDA & filament runout detection. ⚠️
|
|
* Set the jumpers under your drivers to "TMC2208-UART MODE":
|
|
|
|
|
|
## Changes to Start G-code
|
|
The `W` in Prusa's `G28 W ; home all without mesh bed level` G-code does not exist in Marlin and [`G80 ; mesh bed leveling`](https://marlinfw.org/docs/gcode/G080.html) cancels the current motion mode, so no bed leveling will take place.
|
|
|
|
### PrusaSlicer
|
|
Paste the start g-code block below in the Printer Settings tab's Custom G-code section. Use the Filament Settings tab's Custom G-code section to add the [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value since it can be saved on a per-filament basis.
|
|
```gcode
|
|
G90 ; use absolute coordinates
|
|
M83 ; extruder relative mode
|
|
M104 S170 ; preheat extruder to 170
|
|
M140 S[first_layer_bed_temperature] ; set bed temp
|
|
M190 S[first_layer_bed_temperature] ; wait for bed temp
|
|
G28 ; home all
|
|
G29 ; mesh bed leveling
|
|
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area
|
|
M109 S[first_layer_temperature] ; wait for extruder temp
|
|
G92 E0.0
|
|
G1 X60.0 E9.0 F1000.0 ; intro line
|
|
G1 X100.0 E12.5 F1000.0 ; intro line
|
|
G92 E0.0
|
|
```
|
|
|
|
### Cura
|
|
Paste the start g-code block below in the Start G-code section. Don't forget to add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
|
|
```gcode
|
|
G90 ; use absolute coordinates
|
|
M83 ; extruder relative mode
|
|
M900 K0.0 ; place your linear advance value here
|
|
M104 S170 ; preheat extruder to 170
|
|
M140 S{material_bed_temperature_layer_0} ; set bed temp
|
|
M190 S{material_bed_temperature_layer_0} ; wait for bed temp
|
|
G28 ; home all
|
|
G29 ; mesh bed leveling
|
|
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area
|
|
M109 S{material_print_temperature_layer_0} ; wait for extruder temp
|
|
G92 E0.0
|
|
G1 X60.0 E9.0 F1000.0 ; intro line
|
|
G1 X100.0 E12.5 F1000.0 ; intro line
|
|
G92 E0.0
|
|
```
|
|
|
|
### Simplify3D
|
|
Paste the start g-code block below in the Starting Script section. Don't forget to add your [Linear Advance](https://marlinfw.org/docs/features/lin_advance.html) (`M900 K0.0`) value in the start G-code block below:
|
|
```gcode
|
|
G90 ; use absolute coordinates
|
|
M83 ; extruder relative mode
|
|
M900 K0.0 ; place your linear advance value here
|
|
M104 S170 ; preheat extruder to 170
|
|
M140 S[bed0_temperature] ; set bed temp
|
|
M190 S[bed0_temperature] ; wait for bed temp
|
|
G28 ; home all
|
|
G29 ; mesh bed leveling
|
|
G1 X0 Z0.6 Y-3.0 F1000.0 ; go outside print area
|
|
M109 S[extruder0_temperature] T0 ; wait for extruder temp
|
|
G92 E0.0
|
|
G1 X60.0 E9.0 F1000.0 ; intro line
|
|
G1 X100.0 E12.5 F1000.0 ; intro line
|
|
G92 E0.0
|
|
``` |